Work out what you need
How much will your project take?
Tell us the surface and the area. We'll size the coating and add the right prep cleaners for that surface.
Choose a surface and enter your area to see what you need.
Titan Shield Gloss covers up to 150 sq ft per gallon at 3 coats. Coverage varies with surface porosity, texture and application method — these are low-end figures, so a rough or very porous surface may still need more.
Sealer · water-based polyurethane hybrid
Titan Shield Gloss
4.6 · 33 reviewsMade in USAA single-component, water-based polyurethane hybrid sealer for concrete, pavers and block. A tough gloss finish that takes foot, chemical and vehicle traffic, in clear or 17 colors.
- Takes vehicle traffic
- UV stable, inside or out
- 3 coats in a single day
- 5-year warranty, 10 on non-traffic surfaces
What it is
SEMCO Titan Shield Gloss is a single-component, water-based polyurethane hybrid sealer that dries to a tough, UV-stable gloss film. It's for garage floors, driveways, pool decks, pavers and polished concrete, and it's the topcoat over Liquid Membrane and PreStain. It seals and hardens in one product, with no separate primer.
- 3coats in one day
- ~150sq ft per gallon, 3 coats
- 30–45 minbetween coats
- ~48 hfull cure at 72°F
How much do I need?
Sized for 3 coats at ~150 sq ft per gallon. Porous surfaces may need more.
- In stock · ships from Las Vegas, NV
- Free shipping over $99 · delivery time for your address shown at checkout
- 30-day returns · 5-year limited warranty, 10 on non-traffic surfaces
What it is
SEMCO Titan Shield Gloss is a single-component, water-based polyurethane hybrid sealer that dries to a tough, UV-stable gloss film. It's for garage floors, driveways, pool decks, pavers and polished concrete, and it's the topcoat over Liquid Membrane and PreStain. It seals and hardens in one product, with no separate primer.
Contractor or bulk order? Ask for trade pricing · 1-833-211-2297
01 / Where it works
Built for traffic.
Seal concrete, pavers, block and polished floors indoors or out, on its own or over Liquid Membrane and PreStain.
- Garage floorsTakes foot and vehicle traffic. Mix in Non-Skid Additive where floors get wet.
- Driveways & walkwaysA gloss finish that rejuvenates faded concrete and pavers and stands up to weather.
- Pool decksSeals and helps reduce surface heat. Add Non-Skid for wet, bare feet.
- Pavers, block & stampedBrings out the color of pavers, block and stamped or decorative concrete.
- Interior & polished floorsUV stable and water-based, for basements, shops and polished concrete.
- Over Liquid Membrane & PreStainThe topcoat for both. Wait about 2 days after the last membrane coat.
02 / Which prep
Where it fits in the prep.
Titan Shield needs a clean, dry surface. New concrete takes Prep A, weathered concrete or deposits take Prep D, oily slabs get Prep B, and an existing or unknown coating gets Prep C with a test patch. No acid washes.
| Prep | Use it for | Products, in order | Mix |
|---|---|---|---|
| Prep ABefore Titan Shield | New concrete, fully cured (about a month) · dirt and grime | Stone Soap | 1:4 |
| Prep BBefore Titan Shield | Grease, oil, weathering | Power Cleaner, then Stone Soap | Each 1:4 |
| Prep CBefore Titan Shield | Unknown or non-water-based coatings | Power Cleaner, then Nu-Lift, then Power Cleaner | 1:4 · 1:1 · 1:9 |
| Prep DBefore Titan Shield | Efflorescence, mineral deposits, weathered concrete | Nu-Lift, then Stone Soap | Nu-Lift undiluted · Stone Soap 1:4 |
03 / Specs
The numbers.
A single-component, water-based polyurethane hybrid that forms a dense, high-gloss protective film over cementitious surfaces.
Download the data sheet| Type | Single-component, water-based polyurethane hybrid |
|---|---|
| Finish | Gloss |
| Colors | Clear + 17 colors |
| Coverage | ~150 sq ft per gallon at 3 coats |
| Coats | 3 minimum, about 6–8 mil each |
| Dry between coats | 30–45 min, up to 2 hours if humid |
| Full cure | ~48 hours at 72°F |
| Temperature | Not over 90°F, out of direct afternoon sun |
| Max surface moisture | 3% |
| Tools | Woven roller or airless sprayer (17 tip) |
| Traffic | Foot, chemical and vehicle |
| Cleanup | Warm water, straight after use |
Often bought with it

Titan Shield Gloss
1 Gallon / Clear · ★ 4.6 (33)
The full version
Detailed application instructions.
Titan Shield first, then the full prep for your surface, Non-Skid, and the complete garage and pool deck systems.
01 Degrease, then Prep D
You’ll need: a degreaser · Nu-Lift Cleaner · Stone Soap
- Degrease oil and transmission stains first. No coating bonds to oil, and Prep D isn’t a degreaser.
- Wet the slab, apply Nu-Lift Cleaner and work it in with a stiff brush to lift efflorescence and mineral deposits.
- Rinse thoroughly.
- Follow with Stone Soap to clear the residue and rebalance the surface pH, then rinse again.
- Let the slab dry completely. Concrete holds water long after the surface looks dry.
02 Reinforce cracks and joints
You’ll need: Fabric Reinforcement · Liquid Membrane
- Fill anything wider than ¼" with a suitable filler first.
- Coat the crack or joint generously, lay Fabric Reinforcement into the wet film, press it flat.
- Wait 10–15 minutes, then coat over it to encapsulate.
03 Two coats of membrane
Each coat: 15–20 mil. Keep every coat in that range — thicker traps moisture and stays tacky, thinner leaves the membrane short of waterproof.
- Stir well — pigments settle and unstirred product gives uneven color.
- ½" nap roller on an extension pole; cut in the edges with a brush.
- Recoat when it holds no fingerprint. Second coat perpendicular to the first, same day.
- Inspect for pinholes and thin spots before you stop.
04 Cure, then seal
Wait about 2 days after the last coat of membrane, then seal: three coats of Titan Shield Gloss or two of Sealer MATTE, about 6–8 mil per coat, with Non-Skid Additive mixed in. The membrane still needs its full 7-day cure before heavy use.
| Each coat | 15–20 mil · thin and even |
| Membrane coverage | ~200 sq ft per gallon at 2 coats |
| Titan Shield Gloss | ~150 sq ft per gallon at 3 coats |
| SEMCO Sealer MATTE | ~120 sq ft per gallon at 2 coats |
| Sealer over membrane | ~2 days after the last membrane coat |
| Sealer thickness | ~6–8 mil per coat |
| Initial cure | 7 days minimum · longer if humid |
| Temperature | 50–90°F · out of direct sun |
| Prep | Prep D — degrease oil stains first |
01 Clear the surface
You’ll need: Stone Soap · stiff nylon brush · pump sprayer
Prep A is for dirt and grime, and for new concrete that has fully cured (about a month).
- Sweep or blow off loose debris.
- Mix 1 part Stone Soap to 4 parts water.
02 Wash
- Lightly dampen the surface with water first — it stops the cleaner soaking deep into the pores.
- Apply the Stone Soap mix with a pump sprayer and let it sit 2–3 minutes.
- Scrub with a nylon brush or scrub machine.
- Rinse well and make sure no residue is left.
03 Dry, then coat
Let the surface dry completely before any SEMCO coating goes on — below 3% residual moisture.
| Use for | Dirt and grime · new concrete |
| Products | Stone Soap |
| Mix | 1 part Stone Soap : 4 parts water |
| Dwell time | 2–3 minutes |
| Before coating | Fully dry · under 3% moisture |
01 Mix both cleaners
You’ll need: Power Cleaner · Stone Soap · nylon brush · pump sprayer
Prep B is for grease, oil, weathering and tough build-up — and for EPDM, TPO, shingle and bitumen roofs, and for re-prepping cured SEMCO membrane before an extra coat.
- Power Cleaner: 1 part to 4 parts water.
- Stone Soap: 1 part to 4 parts water.
02 Degrease with Power Cleaner
- Lightly dampen the surface with water.
- Apply the Power Cleaner mix with a pump sprayer and let it sit 2–3 minutes.
- Scrub with a nylon brush or scrub machine.
- Rinse well until no residue is left.
03 Follow with Stone Soap
Repeat the same steps with the Stone Soap mix. It lifts the chemical residue Power Cleaner leaves behind and rebalances the surface pH.
04 Dry, then coat
Let the surface dry completely — below 3% residual moisture — before coating.
| Use for | Grease, oil, weathering · EPDM, TPO, shingle, bitumen |
| Products | Power Cleaner, then Stone Soap |
| Mix | Each 1 part : 4 parts water |
| Dwell time | 2–3 minutes each |
| Before coating | Fully dry · under 3% moisture |
01 Mix three solutions
You’ll need: Power Cleaner · Nu-Lift Cleaner · nylon brush · pump sprayer
Prep C is for surfaces with a non-water-based coating, or one you can’t identify.
- Power Cleaner solution 1: 1 part to 4 parts water.
- Nu-Lift solution: 1 part to 1 part water.
- Power Cleaner solution 2: 1 part to 9 parts water.
02 Wash in three passes
- Lightly dampen the surface with water.
- Apply Power Cleaner solution 1, let it sit 2–3 minutes, scrub, and rinse well.
- Repeat with the Nu-Lift solution.
- Finish with Power Cleaner solution 2, then rinse until no residue is left.
03 Test, dry, then coat
Let it dry completely, then coat a small test patch before the full job.
| Use for | Unknown or non-water-based coatings |
| Products | Power Cleaner, then Nu-Lift |
| Mix | 1:4 Power · 1:1 Nu-Lift · 1:9 Power |
| Dwell time | 2–3 minutes each pass |
| Before coating | Test patch · fully dry |
01 Clear and dampen
You’ll need: Nu-Lift Cleaner · Stone Soap · nylon brush
Prep D is for efflorescence, mineral deposits and oxidation — basements, block, brick, stucco, weathered concrete — and for metal, which Nu-Lift etches so the coating bonds.
- Remove loose paint, dust and debris.
- Lightly wet the surface with water.
02 Nu-Lift, undiluted
- Apply Nu-Lift Cleaner undiluted and let it sit 2–3 minutes.
- Scrub with a nylon brush or scrub machine.
- Rinse well.
03 Stone Soap to finish
- Mix 1 part Stone Soap to 4 parts water, apply and let it sit 2–3 minutes.
- Scrub, then rinse until no residue is left.
Stone Soap clears the residue Nu-Lift released and rebalances the surface pH.
04 Dry, then coat
Let it dry completely — hours, not minutes — to below 3% residual moisture.
| Use for | Efflorescence, mineral deposits · metal |
| Products | Nu-Lift, then Stone Soap |
| Mix | Nu-Lift undiluted · Stone Soap 1:4 |
| Dwell time | 2–3 minutes each |
| Before coating | Fully dry · under 3% moisture |
01 Clean the surface
You’ll need: Nu-Lift Cleaner · Stone Soap · Power Cleaner if oily
- New concrete, fully cured (about a month): Prep A — Stone Soap.
- Mineral deposits or efflorescence: Prep D — Nu-Lift, then Stone Soap.
- Oil or grease: Prep B first — Power Cleaner, then Stone Soap.
- Existing or unknown coating: Prep C — Power Cleaner, Nu-Lift, Power Cleaner, then a test patch.
- Let it dry completely — below 3% residual moisture.
02 Mask off
Mask everything that isn’t being sealed. Pull the tape before the sealer fully cures, or it tears the edge.
03 Three coats
You’ll need: woven roller or airless sprayer (17 tip)
- Stir well before use to mix the pigment.
- Roll on a thin, even first coat. It goes on milky and dries clear.
- Let each coat dry — about 30–45 minutes, up to 2 hours when humid.
- Apply a minimum of three coats, about 6–8 mil each. Porous surfaces may need more.
04 Let it cure
Full cure is typically around 48 hours at 72°F — longer when cool or humid. Keep traffic off until then.
| Coverage | ~150 sq ft per gallon at 3 coats |
| Coats | 3 minimum · ~6–8 mil each |
| Dry between coats | 30–45 min · up to 2 hours if humid |
| Full cure | ~48 hours at 72°F |
| Temperature | Out of direct afternoon sun · not over 90°F |
| Max substrate moisture | 3% |
| Cleanup | Warm water, straight after use |
01 Mix it in first
You’ll need: Non-Skid Additive · Titan Shield Gloss or Sealer MATTE
- Lightly shake the Non-Skid container.
- Empty it into the matching container of sealer — one per gallon or per 5-gallon pail.
- Mix thoroughly.
02 Apply the sealer as normal
Prep and apply the sealer following its own instructions — three coats of Titan Shield Gloss or two of Sealer MATTE. Keep stirring as you go so the grit stays mixed through.
03 Let it cure
Keep traffic off until the sealer has fully cured.
| Ratio | 1 container per matching sealer container |
| Sizes | For 1 gallon · for 5 gallons |
| Timing | Mixed in before rolling |
| Use on | Pool decks, walkways, ramps, stairs, garage floors |
01 Clean the deck
You’ll need: Nu-Lift Cleaner · Stone Soap · Power Cleaner if oily
- Weathered concrete, efflorescence or pool-chemical deposits: Prep D — Nu-Lift, then Stone Soap.
- Oil, grease or sunscreen film: Prep B first.
- Let it dry completely — below 3% residual moisture.
02 Add color (optional)
You’ll need: PreStain Color
Apply thin, even coats of PreStain and let it dry 12–24 hours.
03 Seal with Non-Skid mixed in
You’ll need: Titan Shield Gloss · Non-Skid Additive
- Mix Non-Skid Additive into the sealer before you start.
- Apply a minimum of three thin coats, about 6–8 mil each, letting each dry about 30–45 minutes.
04 Cure, then open the pool
Let the sealer cure fully — about 48 hours at 72°F — before foot traffic. Keep undissolved chlorine tablets and granules off the deck afterwards.
| Prep | Prep D · Prep B if oily |
| PreStain | 200–300 sq ft per gallon at 2 coats |
| Titan Shield Gloss | ~150 sq ft per gallon at 3 coats |
| Non-Skid | 1 per matching sealer container |
| Full cure | ~48 hours at 72°F |
Need a hand? Call 1-833-211-2297 or email info@semcoworks.com — the team will check prep, coverage and cure timing before you start.
Questions
The questions worth asking.
What is SEMCO Titan Shield Gloss?
Titan Shield Gloss is an advanced single-component, water-based polyurethane-hybrid sealer that gives cementitious surfaces a durable, protective gloss finish.
What surfaces is Titan Shield Gloss for?
It is ideal for concrete, micro-toppings, pavers, block, and polished concrete, sealing and protecting the surface while enhancing its appearance.
Does Titan Shield Gloss reduce surface heat?
Yes. On pool decks and similar surfaces it helps reduce surface heat while sealing and protecting against weather.
Can I make Titan Shield Gloss non-slip?
Yes. Add the SEMCO Titan Shield Non-Skid Additive to the sealer to improve traction on floors, ramps, and pool decks.
Is Titan Shield Gloss available in colors?
Yes. It comes in clear plus a range of colors such as Rockslide Grey, White, Sequoia Brown, and Sandy Beige.
How many coats and how much do I need?
Three coats minimum, about 150 sq ft per gallon at three coats. Porous surfaces may need more.
How long between coats, and to cure?
About 30–45 minutes between coats, up to 2 hours when humid. Full cure is about 48 hours at 72°F.
Can it go over Liquid Membrane?
Yes. Wait about 2 days after the last coat of membrane before the first coat of Titan Shield.
More questions? Browse every SEMCO FAQ.
Customer reviews









