Project kits

Pick the job. Get the whole kit.

Twelve projects, each with the right cleaner, reinforcement, coat and sealer for that surface. Choose yours and we'll show you the whole kit, in the order you use it.

Find my kit Compare every kit

12: project kits
3: steps: prep, coat, seal
0: primers to buy

01 / Kit finder

What's the job? Here's your kit.

Pick your project and enter the area. You'll see every product the job needs, in the order you use them, and a first estimate. The project page sizes it exactly.

1 · Project

2 · Area in sq ft

Measure every surface you'll coat: walls and floor, or the full roof. Not sure? Use the calculator on the project page.

Your kit

Basements

02 / All projects

Browse every project.

Pick the job. Each page has the right kit, the prep for your surface and a calculator for how much you need.

01 BasementsSeal porous concrete and block against seepage and damp, from the inside.See the kit

02 FoundationsCoat the outside before backfill. Bridges cracks up to 1/4".See the kit

03 Retaining wallsStop efflorescence and spalling on block, concrete or timber.See the kit

04 RoofsEPDM, shingle, metal, torch-down or concrete. No primer needed.See the kit

05 RV roofsEPDM, TPO, fiberglass and aluminum, without primer.See the kit

06 ShowersThe waterproof layer under tile. No pan liner to seam.See the kit

07 PoolsSeal gunite, plaster or fiberglass without replastering.See the kit

08 Fountains & pondsConcrete fountains, ponds and birdbaths, from a pint.See the kit

09 Decks & balconiesA flexible waterproof skin over boards, edges and end grain.See the kit

10 Pool decksGrip and color for a deck walked on wet and barefoot.See the kit

11 Garage floorsStop dusting and salt stains with a membrane and a wear coat.See the kit

12 WalkwaysSeal concrete, pavers, brick and flagstone against water and salt.See the kit

03 / Every kit, side by side

Same system. Different recipe.

Every kit runs prep, reinforce, coat, seal. What changes is the cleaner, how many coats and whether it needs a wear coat on top.

Project	1 · Prep	2 · Reinforce	3 · Main coat	4 · Seal
Basements	Prep D: Nu-Lift, then Stone Soap	Fabric over cracks wider than ¼"	2 coats, ~200 sq ft per gallon	Optional on floors: Titan Shield Gloss or Sealer MATTE
Foundations	Prep D: Nu-Lift, then Stone Soap	Fabric over cracks wider than ¼", moving joints and the footing junction	2 coats on poured concrete (~200 sq ft/gal); block takes 3 (~150)	Not needed
Retaining walls	Prep D: Nu-Lift, then Stone Soap (sand timber with 60-grit)	Fabric over mortar joints and the footing line	2 coats on block or concrete (~200 sq ft/gal); timber takes 3 (~100)	Not needed
Roofs	Prep B on rubber, shingle and torch-down · Prep D on metal and concrete	Fabric on every seam, lap, edge and penetration	2 coats, ~200 sq ft per gallon (add ~25% on corrugated metal)	Not needed
RV roofs	Prep B on EPDM, TPO and fiberglass · Prep D on aluminum	Fabric around every vent, AC flange, skylight and cap joint	2 coats, ~200 sq ft per gallon	Not needed
Showers	Backer board: no cleaner · plywood: sand with 60-grit · old tile: Prep D	Fabric in every joint, corner, the curb and around the drain	2 coats on backer board (~200 sq ft/gal); wood takes 3 (~100)	Not needed
Pools	Prep D: Nu-Lift, then Stone Soap	Fabric over cracks wider than ¼", the floor-to-wall cove and around fittings	3 coats, ~100 sq ft per gallon	Not needed
Fountains & ponds	Prep D: Nu-Lift, then Stone Soap (sand fiberglass first)	Fabric over cracks wider than ¼"	3 coats, ~100 sq ft per gallon	Not needed
Decks & balconies	Prep E: sand to bare wood with 60-grit, no cleaner	Fabric on board joints, cut ends and the house-wall joint	3 coats on bare wood, ~100 sq ft per gallon	Titan Shield Gloss (3 coats) or Sealer MATTE (2), about 2 days after the membrane, with Non-Skid on stairs
Garage floors	Power Cleaner on oil stains, then Prep D	Fabric over cracks, joints and the slab-to-wall perimeter	2 coats, ~200 sq ft per gallon	Titan Shield Gloss (3 coats) or Sealer MATTE (2), about 2 days after the membrane
Pool decks	Prep D (Prep B first if oily)	—	PreStain color optional, then 3 coats of Titan Shield Gloss, ~150 sq ft per gallon	Non-Skid Additive mixed into every container of Titan Shield Gloss
Walkways	Prep D: Nu-Lift, then Stone Soap	—	3 coats of Titan Shield Gloss, ~150 sq ft per gallon. Want no visible finish? Natural Shield instead.	Non-Skid Additive in the Titan Shield Gloss for paths that get wet