Crystal Coat Floor Rejuvenator
- What it is: A water-based latex polymer floor rejuvenator that restores shine and protection to worn floors — no stripping, no wax removal, no special tools.
- Best for: Homeowners, property managers, and facility teams who want to revive dull hardwood, laminate, VCT/linoleum, concrete, stone, terrazzo, or tile floors without the cost and downtime of replacement.
- Stands out because: Applies with a household microfiber mop in thin coats, dries to the touch in about 45 minutes, and a single application holds its shine for up to about 8 months.
- Keep in mind: It's a rejuvenating topcoat, not a structural repair or a permanent refinish — expect to recoat periodically to maintain the shine, and always test on an inconspicuous area first.
Size:1 Quart (covers up 213 sq ft)
Quantity:
💡 Did you know? 1 Quart covers up to:
Wood: up to 210 sq ft*
Tiles: up to 210 sq ft*
* Based on 2 Coats. Coverage may vary based on surface porosity and application method.
No more strip-and-wax cycle
Genuinely multi-surface
Low Odor & Low VOC
Made in USA- No more strip-and-wax cycle. Traditional floor wax needs periodic full stripping and reapplication; Crystal Coat goes on directly over the existing finish and can simply be recoated later — no stripping chemicals or labor-intensive prep.
- Genuinely multi-surface. One product covers hardwood, laminate, VCT/linoleum, concrete, marble and natural stone, terrazzo, and commercial-grade tile — indoors or outdoors.
- Fast, low-effort application. Applies with a household microfiber mop in thin, even coats; dries to the touch in about 45 minutes and is ready for a second coat once the floor shows no imprints underfoot.
- Enhances rather than masks. Dries crystal clear with a deep gloss finish that brings out the natural color and texture of the floor instead of leaving a plastic, waxy look.
- Built for real-world traffic. Resists stains, scuffs, and everyday foot traffic, and is rated for commercial foot and vehicle traffic as well as chemical resistance.
- Affordable alternative to replacement. A fraction of the cost of new flooring, with most projects completed in under a day.
Shine & Finish
- Dries crystal clear with a deep, glossy finish that enhances (rather than hides) the floor's natural color and texture.
- Fills in light surface scratches for a smoother, more uniform look.
- Rejuvenates faded color on worn floors.
Durability & Protection
- Forms a durable barrier resistant to stains and high foot traffic.
- Resistant to chemicals.
- Rated for commercial foot and vehicle traffic.
- Adds traction, helping make floors safer underfoot.
- Protects against water and UV damage.
- One application typically holds its shine for months before a refresh coat is needed.
Application & Convenience
- Applies with a standard household microfiber mop — no special tools, sprayers, or floor buffers required.
- Self-leveling formula for an even, streak-free finish.
- Dries to the touch in about 45 minutes; a second coat can be added the same day for extra durability.
- No wax stripping required, ever — just clean and recoat when it's time to refresh.
- Suitable for interior, exterior, and below-grade applications.
- Water-based latex polymer formula, made in the USA.
- Hardwood and laminate floors — revive dulled, scuffed wood-look flooring without sanding or refinishing.
- VCT and linoleum floors — a modern alternative to the traditional commercial strip-and-wax routine.
- Sealed Concrete floors — add shine and a protective, stain-resistant barrier to garage, basement, or showroom concrete.
- Marble and natural stone — restore luster to entryways, showrooms, and high-traffic stone floors.
- Terrazzo — rejuvenate lobbies and commercial terrazzo without a full refinishing job.
- Commercial-grade tile — bring back shine in retail, hospitality, or office environments with minimal downtime.
- Over existing sealed or finished floors — works over previously sealed surfaces, other SEMCO sealers, stamped concrete, and ceramic tile.
- Prep the surface. Make sure the floor is completely clean, dry, and free of debris. If there's any existing wax coating, remove it before applying Crystal Coat.
- Apply with a microfiber mop. Pour a small amount onto a clean section of floor and spread it in a thin, even coat with a household microfiber mop. Work in small sections at a time. On wood or laminate floors, apply in the direction of the individual planks.
- Let it dry. Only apply at temperatures above 50°F. Allow about 45 minutes of dry time before walking on the floor.
- Apply a second coat if desired, once the first coat is dry enough that walking on it leaves no imprints.
- Let it fully cure for 24 hours before placing heavy furniture or objects back on the floor.
- Touch up as needed. If you miss a spot, wait until the floor is dry, then pour a small amount of Crystal Coat onto a clean microfiber cloth and touch up the area.
- Maintain it. When the shine starts to fade (SEMCO cites roughly 8 months per application), simply clean the surface and apply a fresh coat — no stripping required.
PRODUCT INFO
Engineered for professionals. Easy enough to apply yourself.
SEMCO Crystal Coat is a water-based floor rejuvenator built with the latest latex polymer technology, designed to bring a dull, worn floor back to a like-new shine without stripping it down or replacing it. Instead of the harsh strip-and-rewax cycle that traditional floor finishes require, Crystal Coat is applied directly over the existing surface with a household microfiber mop — it self-levels, dries clear, and cures into a hard, glossy, protective barrier that resists stains, scuffs, and everyday foot traffic.
It's genuinely multi-surface: hardwood, laminate, and VCT/linoleum floors indoors, as well as concrete, marble, natural stone, terrazzo, and commercial-grade tile. Because there's no stripping involved, a full rejuvenation project can typically be finished in under a day, with a single application holding its shine for months.
- Type – Water-based latex polymer
- Coverage – Up to 213 sq ft/quart, up to 850 sq ft/gallon, up to 4,250 sq ft/5-gallon pail
- Application tools – Household microfiber mop
- Application temperature – Above 50°F
- Dry time – About 45 minutes
- VOC – 6.41 g/L
- Shelf life – 2 years in controlled ambient storage (60–72°F)
How Crystal Coat Compares to Traditional Floor Wax
Crystal Coat is positioned by SEMCO specifically as a replacement for the old strip-and-wax routine. Here's how that comparison holds up against general, sourced information on traditional acrylic floor wax finishes (not a specific named product).
| SEMCO Crystal Coat (Water-Based Latex Polymer) |
Traditional Acrylic Floor Wax | |
|---|---|---|
| Stripping required before recoat | ✗ Clean and apply directly over existing finish |
✓ Full strip typically required every few reapplication cycles |
| Typical reapplication interval | ~8 months per application (SEMCO's published figure) | Every 3–24 months depending on traffic level (more frequent in heavy-traffic commercial spaces) |
| Application tool | Household microfiber mop | Mop or auto-scrubber, often with floor buffer/burnisher for maintenance |
| Durability over time | Marketed as long-lasting shine and protection; specific multi-year data not independently published | Known to wear and yellow relatively quickly, requiring more frequent interim maintenance than harder finishes like polyurethane |
| Special equipment needed | ✗ None |
✓ Often requires stripping pads, wet vacuums, and/or burnishing equipment |
| Suitable for DIY application | ✓ | Possible, but full strip-and-wax is more labor-intensive and commonly contracted out |
This comparison reflects general, publicly available information about acrylic wax floor finishes as a category, not a specific competing product. Crystal Coat's own multi-year durability and VOC data are not independently published, so those rows are described qualitatively rather than with precise figures.
SEMCO Liquid Membrane™ is trusted by professional waterproofing contractors, builders, pool service companies, property managers, and facilities teams across the country. We offer dedicated support and volume pricing for businesses.
Benefits List
- Volume discount pricing on 5-gallon pails and case ordersPriority technical support from application experts
- Fast reorder history and account management
- Co-branded project documentation and spec sheets available
- Suitable for: waterproofing contractors, pool builders, property maintenance, HOAs, facility managers
CTAs
- Enquire About Pro Pricing → CONTACT US
- Call Us: 1-833-211-2297
Step by step
FOR STEP-BY-STEP GUIDES SPECIFIC TO YOUR PROJECT
-
1
Prepare your surface and Gather your materials
For concrete or brick surfaces we recommend our Preparation D in order to remove any mineral deposits or efflorescence from the surface. For this you will need the following cleaners : Nu-Lift Cleaner and Stone Soap If there is constant dampness in the substrate, use Natural Shield first to mitigate the moisture. Let it fully cure first prior to applying SEMCO Liquid Membrane™ . Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Fabric Reinforcement
If you have any cracks wider than 1/4", a Fabric Reinforcement is needed to bridge the crack. Any cracks smaller than 1/4" width, SEMCO Liquid Membrane™ can be applied over it. To apply the Fabric Reinforcement, apply a generous coat of SEMCO Liquid Membrane™ over the crack. Put the Fabric Reinforcement on a press it flat, after 10-15 min apply another coat of SEMCO Liquid Membrane™ over the Fabric Reinforcement to encapsulate it. Let it dry to the touch before applying SEMCO Liquid Membrane™ over the entire surface. -
3
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. -
6
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Suitable for light foot traffic.For heavy foot traffic or vehicle traffic, we recommend using SEMCO Titan Shield Gloss. It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. For applications where the product is fully submerged, 3 coats @20mil each is required and allow a curing time of minimum 6-7 days.Also application must coat entire surface to above the waterline. Please note that the SEMCO Liquid Membrane may experience slight color variations or discoloration when exposed to water for extended periods of time. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before permitting water. For applications where SEMCO Liquid Membrane™ is applied on pool plaster, extended curing times might occur as plaster holds more moisture which needs to breath out first. A slight color change may occur when being in contact with water when the product has not fully cured yet. This however will not affect the performance of the SEMCO Liquid Membrane™. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
-
1
Preparation
Sand the wood surface with a 60 grit sandpaper. Take off any loose coating and ensure surface is free of any debrisAs wood often absorbs water, avoid pressure washing wood prior to the application. -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
4
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. -
5
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Suitable for light foot traffic.For heavy foot traffic or vehicle traffic, we recommend using SEMCO Titan Shield Gloss. It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. For applications where the product is fully submerged, 3 coats @20mil each is required and allow a curing time of minimum 6-7 days.Also application must coat entire surface to above the waterline. Please note that the SEMCO Liquid Membrane may experience slight color variations or discoloration when exposed to water for extended periods of time. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before permitting water. For applications where SEMCO Liquid Membrane™ is applied on pool plaster, extended curing times might occur as plaster holds more moisture which needs to breath out first. A slight color change may occur when being in contact with water when the product has not fully cured yet. This however will not affect the performance of the SEMCO Liquid Membrane™. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
-
1
Prepare your space and Gather your materials
For concrete or gunnite surfaces we recommend our Preparation D in order to remove any mineral deposits or efflorescence from the surface. For this you will need the following cleaners : Nu-Lift Cleaner and Stone Soap For fiberglass surfaces it is required to sand the entire surface first with a 60 grit. Afterwards use Preparation B.For this you will need the following cleaners : Power Cleaner and Stone Soap If there is constant dampness in the substrate, use Natural Shield first to mitigate the moisture. Let it fully cure first prior to applying SEMCO Liquid Membrane™ . Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Fabric Reinforcement
If you have any cracks wider than 1/4", a Fabric Reinforcement is needed to bridge the crack. Any cracks smaller than 1/4" width, SEMCO Liquid Membrane™ can be applied over it. -
3
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. For submerged applications a min. required total thickness of 60 mil is required. Allow 6-7 days for full cure to filling with water.For submerged applications we recommend adding Extra Pigment for a more solid overall finish -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. -
6
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. For applications where the product is fully submerged, 3 coats @20mil each is required and allow a curing time of minimum 6-7 days.Also application must coat entire surface to above the waterline. Please note that the SEMCO Liquid Membrane may experience slight color variations or discoloration when exposed to water for extended periods of time. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before permitting water. For applications where SEMCO Liquid Membrane™ is applied on pool plaster, extended curing times might occur as plaster holds more moisture which needs to breath out first. A slight color change may occur when being in contact with water when the product has not fully cured yet. This however will not affect the performance of the SEMCO Liquid Membrane™. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
-
1
Prepare your space and Gather your materials
For bare concrete or water based coatings we recommend our Preparation D in order to remove any mineral deposits or efflorescence from the surface. For this you will need the following cleaners : Nu-Lift Cleaner and Stone Soap For asphalt, rubber and EPDM surfaces we recommend Preparation B.For this you will need the following cleaners : Power Cleaner and Stone Soap Ensure your surfaces are fully cleaned and dried. If you have any rust on your surface, use a water based rust primer first.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Fabric Reinforcement
We strongly recommend using the Fabric Reinforcement on all the joints.Apply a generous coat of SEMCO Liquid Membrane™ on the joints. 4" on each side of the joint and while product is still wet, put the Fabric Reinforcement over the joint and press it flat. Once Fabric Reinforcement is on, apply another coat of SEMCO Liquid Membrane™ across the Fabric Reinforcement to encapsulate it. Let it dry completely before resuming to next step. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. Avoid contact with water during the curing period. -
6
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Please note that the SEMCO Liquid Membrane may experience slight color variations or discoloration when exposed to water for extended periods of time. It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before being fully submerged. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
-
1
Prepare your space and Gather your materials
For bare concrete or water based coatings we recommend our Preparation D in order to remove any mineral deposits or efflorescence from the surface. For this you will need the following cleaners : Nu-Lift Cleaner and Stone Soap For concrete surfaces with oil stains or grease we recommend Preparation B.For this you will need the following cleaners : Power Cleaner and Stone Soap Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Fabric Reinforcement
If you have any cracks wider than 1/4", a Fabric Reinforcement is needed to bridge the crack. Any cracks smaller than 1/4" width, SEMCO Liquid Membrane™ can be applied over it. -
3
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. Avoid contact with water during the curing period. -
6
Additional Information
It is not recommended to apply any of our products to green concrete. Fresh concrete should be allowed to cure for a minimum of 28 days. For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Suitable for light foot traffic.For heavy foot traffic or vehicle traffic, we recommend using SEMCO Titan Shield. It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. For applications where the product is fully submerged, 3 coats @20mil each is required and allow a curing time of minimum 6-7 days.Also application must coat entire surface to above the waterline. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before permitting water. For applications where SEMCO Liquid Membrane™ is applied on pool plaster, extended curing times might occur as plaster holds more moisture which needs to breath out first. A slight color change may occur when being in contact with water when the product has not fully cured yet. This however will not affect the performance of the SEMCO Liquid Membrane™. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
Download as PDF
-
1
Prepare your space and Gather your materials
Use SEMCO Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Use SEMCO Power Cleaner and SEMCO Nu-Lift Cleaner if there is any oil or grease Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Titan Shield Application
Use a 1/2" woven nap roller to apply Titan Shield Gloss. Apply the first coat and allow the sealer to dry for at least 30 - 45 minutes, up to 2 hrs in high humidity conditions, or until surface is completely dry. Repeat the application to a minimum of 3 coats or a total thickness of 15-20 mil. Additional coats may be required depending on the porosity of your substrate. For larger areas Titan Shield Gloss can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first.Apply each coat in alternate directions to the last coat to ensure even coverage. -
4
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application.
-
1
Prepare your space and Gather your materials
Use SEMCO Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Use SEMCO Power Cleaner and SEMCO Nu-Lift Cleaner if there is any oil or grease Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Titan Shield Application
Use a 1/2" woven nap roller to apply Titan Shield Gloss. Apply the first coat and allow the sealer to dry for at least 30 - 45 minutes, up to 2 hrs in high humidity conditions, or until surface is completely dry. Repeat the application to a minimum of 3 coats or a total thickness of 15-20 mil. Additional coats may be required depending on the porosity of your substrate. For larger areas Titan Shield Gloss can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first.Apply each coat in alternate directions to the last coat to ensure even coverage. -
4
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. If SEMCO Liquid Membrane has been applied prior, let it cure for a minimum of 4 days prior to applying Titan Shield.
Download as PDF
-
1
Prepare your space and Gather your materials
Use SEMCO Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Use SEMCO Power Cleaner and SEMCO Nu-Lift Cleaner if there is any oil or grease Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Titan Shield Application
Use a 1/2" woven nap roller to apply Titan Shield Gloss. Apply the first coat and allow the sealer to dry for at least 30 - 45 minutes, up to 2 hrs in high humidity conditions, or until surface is completely dry. Repeat the application to a minimum of 3 coats or a total thickness of 15-20 mil. Additional coats may be required depending on the porosity of your substrate. For larger areas Titan Shield Gloss can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first.Apply each coat in alternate directions to the last coat to ensure even coverage. -
4
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. If SEMCO Liquid Membrane has been applied prior, let it cure for a minimum of 4 days prior to applying Titan Shield. Cure times are displayed in our curing chart.
-
1
Prepare your space and Gather your materials
Use Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Natural Shield Application
Use a 1/4" woven nap roller to apply Natural Shield. Apply the first coat and do not allow sealer to completely dry before applying second and third coats.Repeat the application to a minimum of 3 coats. Additional coats may be required depending on the porosity of your substrate. For larger areas Natural Shield can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first. -
4
Additional Information
For clean up use warm water to clean brush or roller right after use. No existing coating can be on the surface else Natural Shield cannot penetrate into the substrate. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate
-
1
Prepare your space and Gather your materials
Use Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Use Power Cleaner and Nu-Lift Cleaner if there is any oil or grease Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Natural Shield Application
Use a 1/4" woven nap roller to apply Natural Shield. Apply the first coat and do not allow sealer to completely dry before applying second and third coats.Repeat the application to a minimum of 3 coats. Additional coats may be required depending on the porosity of your substrate. For larger areas Natural Shield can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first. -
4
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. No existing coating can be on the surface else Natural Shield cannot penetrate into the substrate. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate
-
1
Prepare your space and Gather your materials
Ensure your surface is free of any debris. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
WASHING PROCESS
Mix 1 part Stone Soap with 4 parts of water Slightly dampen the surface with water. This will prevent cleaners to penetrate deep into the pores of the substrate Apply the Stone Soap mixture lightly with a pump sprayer and allow to sit for 2-3 minutes Scrub the surface using a scrub machine or nylon brush Rinse the surface off well and ensure no residue is left -
3
Additional Information
Always let surface completely dry prior to application of sealers Do not use Muriatic Acid to prep surfaces as residue may lead to adhesion problems Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes.
-
1
Prepare your space and Gather your materials
Ensure your surface is free of any debris. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
WASHING PROCESS
Mix 1 part Stone Soap with 4 parts of water Mix 1 part POWER CLEANER with 4 parts of water Slightly dampen the surface with water. This will prevent cleaners to penetrate deep into the pores of the substrate Apply the POWER CLEANER mixture lightly with a pump sprayer and allow to sit for 2-3 minutes Scrub the surface using a scrub machine or nylon brush Rinse the surface off well and ensure no residue is left Repeat all steps in this task with Stone Soap to clean chemical residue -
3
Additional Information
Always let surface completely dry prior to application of sealers Do not use Muriatic Acid to prep surfaces as residue may lead to adhesion problems
-
1
Prepare your space and Gather your materials
Ensure your surface is free of any debris. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
WASHING PROCESS
Mix 1 part POWER CLEANER with 4 parts of water for POWER CLEANER SOLUTION 1 Mix 1 part POWER CLEANER with 9 parts of water for POWER CLEANER SOLUTION 2 Mix 1 part Nu-Lift CLEANER with 1 part of water Slightly dampen the surface with water. This will prevent cleaners to penetrate deep into the pores of the substrate Apply the POWER CLEANER SOLUTION 1 mixture lightly with a pump sprayer and allow to sit for 2-3 minutes Scrub the surface using a scrub machine or nylon brush Rinse the surface off well and ensure no residue is left Apply Nu-Lift Cleaner solution and repeat all steps. Apply POWER CLEANER SOLUTION 2 and repeat steps for the procedure -
3
Additional Information
Always let surface completely dry prior to application of sealers Do not use Muriatic Acid to prep surfaces as residue may lead to adhesion problems
-
1
Prepare your space and Gather your materials
Ensure your surface is free of any debris. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
WASHING PROCESS
Slightly wet surface with water prior to applying Nu-Lift Cleaner Apply undiluted Nu-Lift Cleaner on to the surface. and allow to sit for 2-3 minutes Scrub the surface using a scrub machine or nylon brush Rinse the surface off well and ensure no residue is left Mix 1 part Stone Soap with 4 parts of water and allow to sit for 2-3 minutes Scrub the surface using a scrub machine or nylon brush Rinse the surface off well and ensure no residue is left -
3
Additional Information
Always let surface completely dry prior to application of sealers Do not use Muriatic Acid to prep surfaces as residue may lead to adhesion problems
-
1
Prepare your surface and Gather your materials
Use SEMCO Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Use SEMCO Power Cleaner and SEMCO Nu-Lift Cleaner if there is any oil or grease Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
PRESTAIN APPLICATION
Apply PreStain Color with sponge, brush, foam roller or airless sprayer with tip size 17 Apply thin and even coats on to concrete. Do not overload application tool with product and avoid leaving puddles on the surface. Repeat application if more color saturation is required. Let it dry for 12 - 24 hours depending on temperature before applying sealer for added protection. -
4
Additional Information
Must apply between 40-90˚F (4.5-32˚C). Do not use if rain is expected within 24 hours. The concrete surface must be completely dry before application. Work in small sections lightly saturating the surface and immediately back-brush or use pad applicator to eliminate puddling, remove excess and evenly distribute PreStain. Over application of stain will lead to surface failure including peeling and cracking. Stir up the product well before use in order to mix up the color pigments. For areas with furniture or heavy foot traffic we recommend using Titan Shield Sealer to protect the surface.
-
1
Prepare your Non-Skid Additive
Lightly shake the Non-Skid container prior to mixing Empty Non-Skid container into Titan Shield Gloss sealer and mix up well.If you need any assistance, feel free to use our live chat or call us! -
2
Titan Shield Application
Use a 1/2" woven nap roller to apply Titan Shield Gloss. Apply the first coat and allow the sealer to dry for at least 30 - 45 minutes, up to 2 hrs in high humidity conditions, or until surface is completely dry. Repeat the application to a minimum of 3 coats or a total thickness of 15-20 mil. Additional coats may be required depending on the porosity of your substrate. For larger areas Titan Shield Gloss can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first.Apply each coat in alternate directions to the last coat to ensure even coverage. -
3
Additional Information
If Non-Skid Additive is used with clear Titan Shield, spray application is recommended For roller application Titan Shield with color is recommended Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Cure times are displayed in our curing chart.
-
1
Easy Application
Ensure your surface is free of any debris. Gather all the products and tools needed for your project. If there are any existing wax coatings, please remove prior to application Use household microfiber mop for application Pour small amount onto clean surface apply thin coat with microfiber mop. Apply small sections at a time. On wood floors or laminate flooring, apply in the directions of the individual planks.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Additional Information
If you miss a spot, wait until floor is dry and pour Crystal Coat onto clean microfiber cloth and touch up spot. Only use when temperatures are above 50F. Allow to dry for 45 minutes before walking on the floor. Only place heavy objects once surface has cured for 24 hours. A 2nd coat can be applied if desired. Apply only once floor is dry enough to walk on without any imprints.
-
1
Prepare your surface and Gather your materials
For Cement / Hardiebacker board applications, ensure that boards are properly installed and sound. -
2
Fabric Reinforcement
For any joints between the boards and the joint between floor and wall, we recommend using the Fabric Reinforcement. To apply the Fabric Reinforcement, apply a generous coat of SEMCO Liquid Membrane™ over the crack. Put the Fabric Reinforcement on a press it flat, after 10-15 min apply another coat of SEMCO Liquid Membrane™ over the Fabric Reinforcement to encapsulate it. Let it dry to the touch before applying SEMCO Liquid Membrane™ over the entire surface. -
3
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. If SEMCO Liquid Membrane is used as a primary waterproofing, you can tile over the next day with regular tile adhesive of your choice.
-
1
Prepare your surface and Gather your materials
For metal surfaces we recommend our Preparation D in order to chemically etch the surface prior to application. For this you will need the following cleaners : Nu-Lift Cleaner and Stone Soap Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Fabric Reinforcement
If you have any joints, Fabric Reinforcement is needed to bridge the joint. To apply the Fabric Reinforcement, apply a generous coat of SEMCO Liquid Membrane™ over the crack. Put the Fabric Reinforcement on a press it flat, after 10-15 min apply another coat of SEMCO Liquid Membrane™ over the Fabric Reinforcement to encapsulate it. Let it dry to the touch before applying SEMCO Liquid Membrane™ over the entire surface. -
3
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. -
6
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Suitable for light foot traffic.For heavy foot traffic or vehicle traffic, we recommend using SEMCO Titan Shield Gloss. It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. For applications where the product is fully submerged, 3 coats @20mil each is required and allow a curing time of minimum 6-7 days.Also application must coat entire surface to above the waterline. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before permitting water. For applications where SEMCO Liquid Membrane™ is applied on pool plaster, extended curing times might occur as plaster holds more moisture which needs to breath out first. A slight color change may occur when being in contact with water when the product has not fully cured yet. This however will not affect the performance of the SEMCO Liquid Membrane™. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
Need Assistance?
OUR TEAM OF EXPERTS ARE STANDING BY TO HELP MAKE SURE YOUR PROJECT IS A SUCCESS.
CALL OR EMAIL US AT: 1-833-211-2297 info@semcoworks.com
CALL OR EMAIL US AT: 1-833-211-2297 info@semcoworks.com
