Natural Shield
- Won't change how your surface looks. No gloss, no color shift — just added protection, so your concrete, stone, or stucco still looks like itself.
- Deeper protection, longer lasting. 6x more active ingredients than typical penetrating sealers, penetrating into the pores instead of sitting on top.
- Works where other sealers can't. Safe to apply on damp surfaces — it can even help dry out a damp substrate before other coatings go on.
- Stops the damage that adds up over time. Guards against freeze-thaw cracking, efflorescence, and mold or mildew staining.
Size:1 Pint Sample
Quantity:
💡 Did you know? 1 Pint Sample covers up to:
* Based on 2 Coats. Coverage may vary based on surface porosity and application method.
Reduces Freeze Thaw Damage
Penetrating Sealer
Low Odor & Low VOC
Made in USA- Durability. Penetrates into the pores and stabilizes the substrate from within, prolonging the life span of the surface and reducing long-term maintenance.
- UV and alkali resistance. UV-resistant and highly alkali-resistant, with effective protection against freeze-thaw damage.
- Built for commercial and industrial use. Excellent chemical resistance and an industrial-strength finish suited to demanding commercial and industrial environments, not just residential touch-ups.
- A real waterproofing sealer. Low water permeability makes it suitable for wet rooms and showers, and it can be applied to damp surfaces where many sealers can’t
be used. - Extends the life of what you already have. Protects the investment in existing mortar, tile, stucco, brick, and natural stone rather than requiring a full resurface.
- Reduces efflorescence and staining. Enhanced water beading, reduced
efflorescence, and protection against stains caused by mold and mildew. - No change in appearance. The treated surface doesn’t become glossy — it stays tackfree with a natural, unsealed look and feel.
- Easy application and clean-up. Apply with an airless sprayer, pump sprayer, or
roller; clean up with SEMCO Stone Soap and water.
- Protects without changing the look of your surface. Natural Shield penetrates into the pores rather than forming a film on top, so treated concrete, stone, or block keeps
its natural color, texture, and matte finish — nothing looks “sealed.” - 6x more active ingredients than most penetrating sealers. A more concentrated formula means deeper penetration and longer-lasting protection compared to typical
off-the-shelf penetrating sealers. - Fights the damage moisture causes over time. Reduces water absorption enough to help prevent freeze-thaw cracking, pitting, spalling, and alkali-silica reaction (ASR) damage in concrete and masonry.
- Works on damp surfaces, even mitigates moisture. Unlike most sealers, Natural Shield tolerates damp substrates and is even used on its own to help mitigate constant dampness before other coatings are applied.
- Commercial and industrial grade, DIY-simple application. Delivers solvent-basedlevel performance and chemical resistance, but goes on with a roller or sprayer and cleans up with water.
- Protects a wide range of surfaces, not just concrete. Suited to existing concrete, stucco, porous natural stone, slump block, tilt-up walls, and X-Bond Microcement - one product across most of a property’s exterior masonry.
- Existing concrete. Penetrates weathered or previously uncoated concrete to reinforce and stabilize it from within, extending the life of older slabs without changing their appearance.
- Stucco. Soaks into porous stucco to reduce water absorption and efflorescence while keeping the original textured look fully intact.
- Porous natural stone. Protects natural stone’s pores against water intrusion and staining without adding shine, preserving the stone’s natural texture and color.
- Slump block. Seals the highly porous surface of slump block against moisture penetration and efflorescence - common in retaining walls and garden walls.
- Block wall and tilt-up wall. Bonds into vertical masonry and tilt-up concrete panels to repel water and resist freeze-thaw cracking, pitting, and spalling over time.
- PreStain finishes. Locks in stained concrete color while adding water and stain resistance, without adding the gloss that would alter the stain’s natural look.
- Cinder block. Works well on cinder block walls to repel water and reduce efflorescence - though cracks wider than hairline need to be filled first, since Natural Shield does not bridge cracks the way a membrane does.
- Brick. Penetrates brick and mortar joints to reduce water absorption and protect against freeze-thaw damage and mold or mildew staining.
- Not recommended for: painted surfaces (the sealer needs open pores to penetrate) or areas with heavy foot or vehicle traffic — for those, SEMCO recommends Titan Shield Gloss instead.
- Ideal projects: exterior stucco and masonry walls, retaining walls, natural stone patios and facades, garden and block walls, brick veneer, existing concrete slabs, showers and wet rooms, and as a moisture-mitigation pre-treatment ahead of other SEMCO coatings.
- Prep the surface. Sweep all debris off the surface. For concrete or brick, remove mineral deposits or efflorescence first with Nu-Lift Cleaner and Stone Soap. The surface must have open pores — Natural Shield cannot penetrate a painted or
previously coated surface. - Fill any cracks first. Natural Shield does not bridge or span cracks, so cracks need to be filled before application.
- Apply the first coat with a 1/4" nap roller, HVLP sprayer, pump sprayer, or airless sprayer (tip size 15 at roughly 400 PSI). Avoid letting the product puddle - puddling causes a white haze.
- Apply the second and third coats without letting the sealer dry in between. This is the opposite of a topical sealer: Natural Shield needs to stay wet through all 3 coats to bond and penetrate properly.
- Apply a minimum of 3 coats. More porous surfaces such as concrete or block may need additional coats.
- On vertical surfaces, apply from bottom to top to avoid runs, and avoid overspray.
- Let it dry and cure. Dry to the touch in about 30 minutes at 72°F; full cure takes about 7 days at 72°F (as fast as 4 days at 100°F).
Good to know: Avoid application in direct afternoon sun or above 85°F. Clean tools with warm water (and Stone Soap, if needed) right after use.
PRODUCT INFO
Engineered for professionals. Easy enough to apply yourself.
Natural Shield is a ready-to-use, water-based penetrating sealer built for concrete, masonry, stucco, and natural stone. Unlike a topical sealer that sits on top of the surface, Natural Shield’s low molecular weight lets it soak into the pores of the substrate, where a chemical reaction creates a solid, breathable membrane from within. The result is durability and performance that matches a solvent-based system, with the easy application and water clean-up of a water-based product.
Because it penetrates rather than coats, Natural Shield leaves your surface’s natural look completely intact — no gloss, no color change, no shift in texture. That makes it the go-to choice for protecting existing concrete, stucco, block walls, and natural stone from water intrusion, efflorescence, and freeze-thaw damage, in both commercial and industrial settings, without changing how the surface looks or feels.
- Type – Water based Silane and siloxane
- Coats required – Minimum 3 coats, applied wet-on-wet (do not let the sealer dry between coats 1-3)
- Coverage – 150–350 sq ft per gallon (3 coats)
- Application tools – 1/4" nap roller, HVLP sprayer, pump sprayer, or airless sprayer
- Application temperature – 50°F to 90°F
- Dry time – only ~10-30 minutes needed between coats at 72°F
- Cure time – 7 days at 72°F (as fast as 4 days at 100°F)
- Shelf life – 2 years in controlled ambient storage (60–72°F)
Laboratory test results: water - excellent; alkali resistance - excellent;
used motor oil - good;
transmission fluid - good;
10% hydraulic acid - good.
Application notes: Do not allow the sealer to puddle during application - puddling causes a white haze. Do not apply over an existing coating; the surface needs open pores for Natural Shield to penetrate. On vertical surfaces, apply from bottom to top to avoid runs, and avoid overspray.
PRODUCT DATA SHEET
6. Natural Shield vs. Titan Shield Gloss — Which One Do You Need?
Both are SEMCO sealers, but they solve different problems. Use this to help customers pick the right one (or point them to both, since Natural Shield is often used as a prep step before Titan Shield Gloss on damp substrates).
| Natural Shield | Titan Shield Gloss | |
|---|---|---|
| How it works | Penetrates into pores; chemical reaction from within | Forms a topical film on the surface |
| Finish | No visible change — natural, matte look | Visible gloss finish, available in 18 colors |
| Traffic rating | Light foot traffic only | Commercial and industrial vehicle traffic |
| Can it go on damp substrates? | Yes — can even help mitigate dampness | No — requires substrate moisture under 3–5% |
| Typical use | Stucco, natural stone, block walls, brick, existing concrete | Garage floors, driveways, pool decks, high-traffic commercial floors |
| Coats | Minimum 3, applied wet-on-wet | Minimum 3, each allowed to dry before recoating |
SEMCO Liquid Membrane™ is trusted by professional waterproofing contractors, builders, pool service companies, property managers, and facilities teams across the country. We offer dedicated support and volume pricing for businesses.
Benefits List
- Volume discount pricing on 5-gallon pails and case ordersPriority technical support from application experts
- Fast reorder history and account management
- Co-branded project documentation and spec sheets available
- Suitable for: waterproofing contractors, pool builders, property maintenance, HOAs, facility managers
CTAs
- Enquire About Pro Pricing → CONTACT US
- Call Us: 1-833-211-2297
Step by step
FOR STEP-BY-STEP GUIDES SPECIFIC TO YOUR PROJECT
-
1
Prepare your surface and Gather your materials
For concrete or brick surfaces we recommend our Preparation D in order to remove any mineral deposits or efflorescence from the surface. For this you will need the following cleaners : Nu-Lift Cleaner and Stone Soap If there is constant dampness in the substrate, use Natural Shield first to mitigate the moisture. Let it fully cure first prior to applying SEMCO Liquid Membrane™ . Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Fabric Reinforcement
If you have any cracks wider than 1/4", a Fabric Reinforcement is needed to bridge the crack. Any cracks smaller than 1/4" width, SEMCO Liquid Membrane™ can be applied over it. To apply the Fabric Reinforcement, apply a generous coat of SEMCO Liquid Membrane™ over the crack. Put the Fabric Reinforcement on a press it flat, after 10-15 min apply another coat of SEMCO Liquid Membrane™ over the Fabric Reinforcement to encapsulate it. Let it dry to the touch before applying SEMCO Liquid Membrane™ over the entire surface. -
3
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. -
6
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Suitable for light foot traffic.For heavy foot traffic or vehicle traffic, we recommend using SEMCO Titan Shield Gloss. It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. For applications where the product is fully submerged, 3 coats @20mil each is required and allow a curing time of minimum 6-7 days.Also application must coat entire surface to above the waterline. Please note that the SEMCO Liquid Membrane may experience slight color variations or discoloration when exposed to water for extended periods of time. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before permitting water. For applications where SEMCO Liquid Membrane™ is applied on pool plaster, extended curing times might occur as plaster holds more moisture which needs to breath out first. A slight color change may occur when being in contact with water when the product has not fully cured yet. This however will not affect the performance of the SEMCO Liquid Membrane™. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
-
1
Preparation
Sand the wood surface with a 60 grit sandpaper. Take off any loose coating and ensure surface is free of any debrisAs wood often absorbs water, avoid pressure washing wood prior to the application. -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
4
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. -
5
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Suitable for light foot traffic.For heavy foot traffic or vehicle traffic, we recommend using SEMCO Titan Shield Gloss. It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. For applications where the product is fully submerged, 3 coats @20mil each is required and allow a curing time of minimum 6-7 days.Also application must coat entire surface to above the waterline. Please note that the SEMCO Liquid Membrane may experience slight color variations or discoloration when exposed to water for extended periods of time. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before permitting water. For applications where SEMCO Liquid Membrane™ is applied on pool plaster, extended curing times might occur as plaster holds more moisture which needs to breath out first. A slight color change may occur when being in contact with water when the product has not fully cured yet. This however will not affect the performance of the SEMCO Liquid Membrane™. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
-
1
Prepare your space and Gather your materials
For concrete or gunnite surfaces we recommend our Preparation D in order to remove any mineral deposits or efflorescence from the surface. For this you will need the following cleaners : Nu-Lift Cleaner and Stone Soap For fiberglass surfaces it is required to sand the entire surface first with a 60 grit. Afterwards use Preparation B.For this you will need the following cleaners : Power Cleaner and Stone Soap If there is constant dampness in the substrate, use Natural Shield first to mitigate the moisture. Let it fully cure first prior to applying SEMCO Liquid Membrane™ . Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Fabric Reinforcement
If you have any cracks wider than 1/4", a Fabric Reinforcement is needed to bridge the crack. Any cracks smaller than 1/4" width, SEMCO Liquid Membrane™ can be applied over it. -
3
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. For submerged applications a min. required total thickness of 60 mil is required. Allow 6-7 days for full cure to filling with water.For submerged applications we recommend adding Extra Pigment for a more solid overall finish -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. -
6
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. For applications where the product is fully submerged, 3 coats @20mil each is required and allow a curing time of minimum 6-7 days.Also application must coat entire surface to above the waterline. Please note that the SEMCO Liquid Membrane may experience slight color variations or discoloration when exposed to water for extended periods of time. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before permitting water. For applications where SEMCO Liquid Membrane™ is applied on pool plaster, extended curing times might occur as plaster holds more moisture which needs to breath out first. A slight color change may occur when being in contact with water when the product has not fully cured yet. This however will not affect the performance of the SEMCO Liquid Membrane™. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
-
1
Prepare your space and Gather your materials
For bare concrete or water based coatings we recommend our Preparation D in order to remove any mineral deposits or efflorescence from the surface. For this you will need the following cleaners : Nu-Lift Cleaner and Stone Soap For asphalt, rubber and EPDM surfaces we recommend Preparation B.For this you will need the following cleaners : Power Cleaner and Stone Soap Ensure your surfaces are fully cleaned and dried. If you have any rust on your surface, use a water based rust primer first.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Fabric Reinforcement
We strongly recommend using the Fabric Reinforcement on all the joints.Apply a generous coat of SEMCO Liquid Membrane™ on the joints. 4" on each side of the joint and while product is still wet, put the Fabric Reinforcement over the joint and press it flat. Once Fabric Reinforcement is on, apply another coat of SEMCO Liquid Membrane™ across the Fabric Reinforcement to encapsulate it. Let it dry completely before resuming to next step. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. Avoid contact with water during the curing period. -
6
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Please note that the SEMCO Liquid Membrane may experience slight color variations or discoloration when exposed to water for extended periods of time. It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before being fully submerged. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
-
1
Prepare your space and Gather your materials
For bare concrete or water based coatings we recommend our Preparation D in order to remove any mineral deposits or efflorescence from the surface. For this you will need the following cleaners : Nu-Lift Cleaner and Stone Soap For concrete surfaces with oil stains or grease we recommend Preparation B.For this you will need the following cleaners : Power Cleaner and Stone Soap Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Fabric Reinforcement
If you have any cracks wider than 1/4", a Fabric Reinforcement is needed to bridge the crack. Any cracks smaller than 1/4" width, SEMCO Liquid Membrane™ can be applied over it. -
3
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. Avoid contact with water during the curing period. -
6
Additional Information
It is not recommended to apply any of our products to green concrete. Fresh concrete should be allowed to cure for a minimum of 28 days. For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Suitable for light foot traffic.For heavy foot traffic or vehicle traffic, we recommend using SEMCO Titan Shield. It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. For applications where the product is fully submerged, 3 coats @20mil each is required and allow a curing time of minimum 6-7 days.Also application must coat entire surface to above the waterline. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before permitting water. For applications where SEMCO Liquid Membrane™ is applied on pool plaster, extended curing times might occur as plaster holds more moisture which needs to breath out first. A slight color change may occur when being in contact with water when the product has not fully cured yet. This however will not affect the performance of the SEMCO Liquid Membrane™. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
Download as PDF
-
1
Prepare your space and Gather your materials
Use SEMCO Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Use SEMCO Power Cleaner and SEMCO Nu-Lift Cleaner if there is any oil or grease Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Titan Shield Application
Use a 1/2" woven nap roller to apply Titan Shield Gloss. Apply the first coat and allow the sealer to dry for at least 30 - 45 minutes, up to 2 hrs in high humidity conditions, or until surface is completely dry. Repeat the application to a minimum of 3 coats or a total thickness of 15-20 mil. Additional coats may be required depending on the porosity of your substrate. For larger areas Titan Shield Gloss can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first.Apply each coat in alternate directions to the last coat to ensure even coverage. -
4
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application.
-
1
Prepare your space and Gather your materials
Use SEMCO Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Use SEMCO Power Cleaner and SEMCO Nu-Lift Cleaner if there is any oil or grease Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Titan Shield Application
Use a 1/2" woven nap roller to apply Titan Shield Gloss. Apply the first coat and allow the sealer to dry for at least 30 - 45 minutes, up to 2 hrs in high humidity conditions, or until surface is completely dry. Repeat the application to a minimum of 3 coats or a total thickness of 15-20 mil. Additional coats may be required depending on the porosity of your substrate. For larger areas Titan Shield Gloss can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first.Apply each coat in alternate directions to the last coat to ensure even coverage. -
4
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. If SEMCO Liquid Membrane has been applied prior, let it cure for a minimum of 4 days prior to applying Titan Shield.
Download as PDF
-
1
Prepare your space and Gather your materials
Use SEMCO Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Use SEMCO Power Cleaner and SEMCO Nu-Lift Cleaner if there is any oil or grease Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Titan Shield Application
Use a 1/2" woven nap roller to apply Titan Shield Gloss. Apply the first coat and allow the sealer to dry for at least 30 - 45 minutes, up to 2 hrs in high humidity conditions, or until surface is completely dry. Repeat the application to a minimum of 3 coats or a total thickness of 15-20 mil. Additional coats may be required depending on the porosity of your substrate. For larger areas Titan Shield Gloss can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first.Apply each coat in alternate directions to the last coat to ensure even coverage. -
4
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. If SEMCO Liquid Membrane has been applied prior, let it cure for a minimum of 4 days prior to applying Titan Shield. Cure times are displayed in our curing chart.
-
1
Prepare your space and Gather your materials
Use Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Natural Shield Application
Use a 1/4" woven nap roller to apply Natural Shield. Apply the first coat and do not allow sealer to completely dry before applying second and third coats.Repeat the application to a minimum of 3 coats. Additional coats may be required depending on the porosity of your substrate. For larger areas Natural Shield can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first. -
4
Additional Information
For clean up use warm water to clean brush or roller right after use. No existing coating can be on the surface else Natural Shield cannot penetrate into the substrate. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate
-
1
Prepare your space and Gather your materials
Use Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Use Power Cleaner and Nu-Lift Cleaner if there is any oil or grease Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
Natural Shield Application
Use a 1/4" woven nap roller to apply Natural Shield. Apply the first coat and do not allow sealer to completely dry before applying second and third coats.Repeat the application to a minimum of 3 coats. Additional coats may be required depending on the porosity of your substrate. For larger areas Natural Shield can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first. -
4
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. No existing coating can be on the surface else Natural Shield cannot penetrate into the substrate. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate
-
1
Prepare your space and Gather your materials
Ensure your surface is free of any debris. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
WASHING PROCESS
Mix 1 part Stone Soap with 4 parts of water Slightly dampen the surface with water. This will prevent cleaners to penetrate deep into the pores of the substrate Apply the Stone Soap mixture lightly with a pump sprayer and allow to sit for 2-3 minutes Scrub the surface using a scrub machine or nylon brush Rinse the surface off well and ensure no residue is left -
3
Additional Information
Always let surface completely dry prior to application of sealers Do not use Muriatic Acid to prep surfaces as residue may lead to adhesion problems Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes.
-
1
Prepare your space and Gather your materials
Ensure your surface is free of any debris. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
WASHING PROCESS
Mix 1 part Stone Soap with 4 parts of water Mix 1 part POWER CLEANER with 4 parts of water Slightly dampen the surface with water. This will prevent cleaners to penetrate deep into the pores of the substrate Apply the POWER CLEANER mixture lightly with a pump sprayer and allow to sit for 2-3 minutes Scrub the surface using a scrub machine or nylon brush Rinse the surface off well and ensure no residue is left Repeat all steps in this task with Stone Soap to clean chemical residue -
3
Additional Information
Always let surface completely dry prior to application of sealers Do not use Muriatic Acid to prep surfaces as residue may lead to adhesion problems
-
1
Prepare your space and Gather your materials
Ensure your surface is free of any debris. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
WASHING PROCESS
Mix 1 part POWER CLEANER with 4 parts of water for POWER CLEANER SOLUTION 1 Mix 1 part POWER CLEANER with 9 parts of water for POWER CLEANER SOLUTION 2 Mix 1 part Nu-Lift CLEANER with 1 part of water Slightly dampen the surface with water. This will prevent cleaners to penetrate deep into the pores of the substrate Apply the POWER CLEANER SOLUTION 1 mixture lightly with a pump sprayer and allow to sit for 2-3 minutes Scrub the surface using a scrub machine or nylon brush Rinse the surface off well and ensure no residue is left Apply Nu-Lift Cleaner solution and repeat all steps. Apply POWER CLEANER SOLUTION 2 and repeat steps for the procedure -
3
Additional Information
Always let surface completely dry prior to application of sealers Do not use Muriatic Acid to prep surfaces as residue may lead to adhesion problems
-
1
Prepare your space and Gather your materials
Ensure your surface is free of any debris. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
WASHING PROCESS
Slightly wet surface with water prior to applying Nu-Lift Cleaner Apply undiluted Nu-Lift Cleaner on to the surface. and allow to sit for 2-3 minutes Scrub the surface using a scrub machine or nylon brush Rinse the surface off well and ensure no residue is left Mix 1 part Stone Soap with 4 parts of water and allow to sit for 2-3 minutes Scrub the surface using a scrub machine or nylon brush Rinse the surface off well and ensure no residue is left -
3
Additional Information
Always let surface completely dry prior to application of sealers Do not use Muriatic Acid to prep surfaces as residue may lead to adhesion problems
-
1
Prepare your surface and Gather your materials
Use SEMCO Nu-Lift Cleaner and Stone Soap to remove any mineral deposits or efflorescence Use SEMCO Power Cleaner and SEMCO Nu-Lift Cleaner if there is any oil or grease Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
3
PRESTAIN APPLICATION
Apply PreStain Color with sponge, brush, foam roller or airless sprayer with tip size 17 Apply thin and even coats on to concrete. Do not overload application tool with product and avoid leaving puddles on the surface. Repeat application if more color saturation is required. Let it dry for 12 - 24 hours depending on temperature before applying sealer for added protection. -
4
Additional Information
Must apply between 40-90˚F (4.5-32˚C). Do not use if rain is expected within 24 hours. The concrete surface must be completely dry before application. Work in small sections lightly saturating the surface and immediately back-brush or use pad applicator to eliminate puddling, remove excess and evenly distribute PreStain. Over application of stain will lead to surface failure including peeling and cracking. Stir up the product well before use in order to mix up the color pigments. For areas with furniture or heavy foot traffic we recommend using Titan Shield Sealer to protect the surface.
-
1
Prepare your Non-Skid Additive
Lightly shake the Non-Skid container prior to mixing Empty Non-Skid container into Titan Shield Gloss sealer and mix up well.If you need any assistance, feel free to use our live chat or call us! -
2
Titan Shield Application
Use a 1/2" woven nap roller to apply Titan Shield Gloss. Apply the first coat and allow the sealer to dry for at least 30 - 45 minutes, up to 2 hrs in high humidity conditions, or until surface is completely dry. Repeat the application to a minimum of 3 coats or a total thickness of 15-20 mil. Additional coats may be required depending on the porosity of your substrate. For larger areas Titan Shield Gloss can be applied with an airless sprayer with tip size 17. Adjust the sprayer to the lowest possible air setting and try out on a test area first.Apply each coat in alternate directions to the last coat to ensure even coverage. -
3
Additional Information
If Non-Skid Additive is used with clear Titan Shield, spray application is recommended For roller application Titan Shield with color is recommended Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Cure times are displayed in our curing chart.
-
1
Easy Application
Ensure your surface is free of any debris. Gather all the products and tools needed for your project. If there are any existing wax coatings, please remove prior to application Use household microfiber mop for application Pour small amount onto clean surface apply thin coat with microfiber mop. Apply small sections at a time. On wood floors or laminate flooring, apply in the directions of the individual planks.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Additional Information
If you miss a spot, wait until floor is dry and pour Crystal Coat onto clean microfiber cloth and touch up spot. Only use when temperatures are above 50F. Allow to dry for 45 minutes before walking on the floor. Only place heavy objects once surface has cured for 24 hours. A 2nd coat can be applied if desired. Apply only once floor is dry enough to walk on without any imprints.
-
1
Prepare your surface and Gather your materials
For Cement / Hardiebacker board applications, ensure that boards are properly installed and sound. -
2
Fabric Reinforcement
For any joints between the boards and the joint between floor and wall, we recommend using the Fabric Reinforcement. To apply the Fabric Reinforcement, apply a generous coat of SEMCO Liquid Membrane™ over the crack. Put the Fabric Reinforcement on a press it flat, after 10-15 min apply another coat of SEMCO Liquid Membrane™ over the Fabric Reinforcement to encapsulate it. Let it dry to the touch before applying SEMCO Liquid Membrane™ over the entire surface. -
3
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. If SEMCO Liquid Membrane is used as a primary waterproofing, you can tile over the next day with regular tile adhesive of your choice.
-
1
Prepare your surface and Gather your materials
For metal surfaces we recommend our Preparation D in order to chemically etch the surface prior to application. For this you will need the following cleaners : Nu-Lift Cleaner and Stone Soap Ensure your surfaces are fully cleaned and dried. Gather all the products and tools needed for your project.If you need assistance with which cleaners are needed for the Prep, feel free to use our live chat or call us! -
2
Fabric Reinforcement
If you have any joints, Fabric Reinforcement is needed to bridge the joint. To apply the Fabric Reinforcement, apply a generous coat of SEMCO Liquid Membrane™ over the crack. Put the Fabric Reinforcement on a press it flat, after 10-15 min apply another coat of SEMCO Liquid Membrane™ over the Fabric Reinforcement to encapsulate it. Let it dry to the touch before applying SEMCO Liquid Membrane™ over the entire surface. -
3
Masking
Mask off areas that are not receiving any coating. Remove masking tape before material has fully cured. -
4
APPLYING COAT
Use a 1/2" nap roller. Allow any pre-treated areas to fully dry. Apply a thin coat (0.015 inch per coat) of SEMCO Liquid Membrane™ with brush or roller over substrate including pre-treated areas. Once you can walk on the surface and not get any residue on your shoe or feet or cannot leave a fingerprint impression it is ready to re-coat. Apply another thin coat of SEMCO Liquid Membrane™ in an alternate direction over the first coat of SEMCO Liquid Membrane™. Let topcoat dry to the touch, approximately 1–2 hours at 70 °F (21 °C) and 50% RH. When last coat has dried to the touch, inspect final surface for pinholes, voids, thin spots or other defects.SEMCO Liquid Membrane™ will dry to a lighter color when it’s dry to touch. Use additional SEMCO Liquid Membrane™ to seal the defects. Required total thickness is 0.03 - 0.04 inches for non submerged applications. -
5
Curing Time
Curing time depends on temperature, humidity and airflow, however typically initial cure is within 6 - 7 days as per specific product recommendations. -
6
Additional Information
For clean up use warm water to clean brush or roller right after use. For optimal bonding we highly recommend preparing the surface as mentioned above for best results. Stir up the product well before use in order to mix up the color pigments. Avoid application in direct sun light in the afternoon or temperatures of over 85F as it might cause the product to dry too fast before it can adhere to the substrate Suitable for light foot traffic.For heavy foot traffic or vehicle traffic, we recommend using SEMCO Titan Shield Gloss. It can not be applied to wet substrates or substrates still containing moisture, else it will not cure correctly and stay tacky. Max. rest moisture in substrate can be up to 3%. If you are unsure about the moisture content, have it measured prior to application. Ensuring that a surface is pH balanced before applying a coating is crucial for optimal adhesion and performance. Therefore we recommend our preparation methods for optimal adhesion. We do not recommend acid washes. For applications where the product is fully submerged, 3 coats @20mil each is required and allow a curing time of minimum 6-7 days.Also application must coat entire surface to above the waterline. Application on non porous surfaces such as metal or fiberglass : Apply thin coats as this will allow for the product to cure faster. Cure times are displayed in our curing chart. However if coats have been applied too thick, the surface might feel tacky. This is a sign of trapped moisture. If you have left over product, apply a very thin coat over the entire surface. The surface needs to be fully cured and hard before permitting water. For applications where SEMCO Liquid Membrane™ is applied on pool plaster, extended curing times might occur as plaster holds more moisture which needs to breath out first. A slight color change may occur when being in contact with water when the product has not fully cured yet. This however will not affect the performance of the SEMCO Liquid Membrane™. It is always advisable to apply a small test patch in an inconspicuous are to ensure adequate adhesion prior to full application. If you have multiple containers of SEMCO Liquid Membrane™, we highly recommend to either mix them together or use one container for the last layer to get color consistency.
Need Assistance?
OUR TEAM OF EXPERTS ARE STANDING BY TO HELP MAKE SURE YOUR PROJECT IS A SUCCESS.
CALL OR EMAIL US AT: 1-833-211-2297 info@semcoworks.com
CALL OR EMAIL US AT: 1-833-211-2297 info@semcoworks.com
